RSM process optimization of biodiesel production from rapeseed oil and waste corn oil in the presence of green and novel catalyst

Scientific Reports volume 12, Article number: 19652 (2022) Cite this article 1597 Accesses 5 Citations Metrics details In the scenario of global warming and pollution, the green synthesis and use of

Scientific Reports volume 12, Article number: 19652 (2022) Cite this article

1597 Accesses

5 Citations

Metrics details

In the scenario of global warming and pollution, the green synthesis and use of biodiesel has acquired utmost priority. Due to several limitations of homogeneous catalysis, organobase immobilized heterogeneous catalyzed production of biodiesel has come out as a favored route. The present report demonstrates the design and synthesis of Peganum harmala spice seed extract modified GO-CuFe2O4 (SSE@GO-CuFe2O4) nanocomposite as an organobase functionalized high surface area magnetic nanocatalyst. Pistachio leaves were used in the green reduction of precursor salts to synthesize CuFe2O4 NPs. The as-synthesized nanomaterial was characterized physicochemically by Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy dispersive X-Ray analysis (EDX), elemental mapping, transmission electron microscopy (TEM), X-Ray diffraction (XRD), thermogravimetric analysis (TGA) and vibrating sample magnetometer techniques (VSM). Subsequently, the catalyst was explored in the efficient synthesis of biodiesels by trans-esterification of two substrates, the rapeseed oil and waste corn oil. The optimum conditions for biodiesel production were determined through response surface methodology based on Box–Behnken design including the study of calibration curves and 3D contour plots. Easy separation and workup, use of green medium, excellent reused for several times and short reaction time are outstanding benefits of this study.

In recent times, the extravagant consumption of natural energy resources, the ever-increasing environmental pollution and the resulting global warming is a serious concern worldwide. Industrial development and upgradation in the standard of living in the society has made the circumstances more dreadful1,2,3. The storage of fossil fuel has been literally going to be exhausted and this has persuaded the scientists to rethink about the generation of non-conventional energy from renewable sources and also developing advanced technological methodologies that would retard the energy consumption and reduces hazardous wastes thereby leading to sustainability4,5,6,7,8. The extensive research has demonstrated that biofuels, more precisely, the biodiesels could be the best possible solution as a promising and featured green fuel towards alternant energy9,10,11,12. In contradiction to fossil fuels, biodiesels are beneficial with regards to its higher oxygen content, devoid of sulphur and carcinogen content, reproducibility, inexpensive and abundant precursors, biodegradability, eco-friendliness, minimally toxic and very low exhaust emissions to the environment, although they are having equivalent calorific value to fossil fuels while burning13,14,15,16,17. In addition, biodiesels possess higher combustion efficiency and cetane number and also having outstanding lubricity. Due to higher flash point, the biodiesel is also much safe to store, handling and transport than conventional fuels18,19,20. Although, the bio-diesels are costly now-a-days than petro fuels, in view of these favorable issues, a number of research groups around the world are engaged in developing the synthesis protocol in order to cut down the production cost.

Usually, biodiesels are produced following different pathways like micro emulsion, pyrolysis and transesterification and among them the last one is most facile, handy and sustainable9,10. Transesterfication involves the alcoholysis, mainly methanolysis of esters, being obtained from different feedstock like waste cooking oil, bio-wastes, agricultural wastes, animal fats, vegetable oil and also from the natural resources like non-edible jatropha oil, canola oil, neem oil, tea oil, cotton oil, tobacco oiletc and edible soybean oil, palm oil, coconut oil, castor oil21,22,23,24,25,26,27,28,29,30,31,32,33,34.

In the recent years, quite a number of researcher have accounted the proficient synthesis of methyl ester biodiesel applying different homogeneous or heterogeneous acid or base catalysts. Keeping in mind of recent trend for green and sustainable protocols, heterogeneous catalysts has proven their dominance over the former in all domains of catalysis35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51. In this context, different architectured nanomaterials have come upon as the protagonist of heterogeneous catalysts. Particularly, the biomolecularly modified magnetic nanoparticles (NP) have garnered significant attention these days based on their high surface to volume ratio, larger number of surface atoms or active sites, exceptional mechanochemical and thermal stability, biocompatibility, effortless isolation from the system by just using an external magnet and reusability with consistent reactivity52,53,54,55,56,57,58,59,60,61,62,63,64,65.

With all these inputs, this work demonstrate the novel engineered synthesis of Peganum harmala spice seed extract (SSE) immobilized over graphene oxide (GO) and CuFe2O4 nanocomposite and subsequent application of the material in the transesterification waste corn oil and rapeseed oil towards the synthesis of bio-diesels65. The Peganum harmala, commonly known as Syrian or African rue, linked to Zygophyllacea family, is a wild flowering plant and grows abundantly in Middle East and North African countries. The seed extract contains large extent of β-carbolines such asharmaline, harmine, harmalol, harmol, tetrahydroharmine, and the quinazoline derivatives like vasicinone and deoxyvasicinone66,67,68. Both these nitrogen containing heterocyclic scaffolds are basic in nature which has been the driving force behind its excellent catalytic potential in trans-esterification. CuFe2O4 doped GO was used as the base matrix in view of exploiting the high surface area of GO as well as the easy magnetic reusability due to ferrite. Green pistachio leaf extract was used as the green reductant in the production of GO-CuFe2O4 composite65. To the best perception, this report on the biodiesel synthesis (Fig. 1) from waste corn oil and rapeseed oil catalyzed over green synthesized magnetic nanocomposite (SSE@GO-CuFe2O4) is unprecedented.

General reaction scheme for transesterification.

Optimization of the reaction parameters such as molar ratio of methanol to oil, amount of catalyst, volume of water usedand reaction time through Response Surface Methodology (RSM)is another important wing of this study. It is a combined statistical and mathematical approach having wide applicability69,70,71. The optimization protocol involves the drawing of contours and curves in 2-D or 3-D planes and from the corresponding shapes the interaction between the variables are illustrated. The effects of the parameters and their interactions were studied through Analysis of variance (ANOVA).

This section includes several segments including material, methods and the experimental details.

All the chemicals and solvents were procured from Sigma-Aldrich and Merck from USA and Germany and used without further purification (99.9% pure). NaNO3, KMnO4, CuCl2·2H2O, FeCl3·6H2O, NaOH, MeOH and EtOH were used for this project. Good quality rapeseed oil and waste corn oil were collected from market. The particle size and morphology were determined by measuring SEM using FESEM-TESCAN MIRA3 instrument (Czeck Republic). FT-IR analysis was performed on KBr pellets in a BRUKER spectrophotometer (model VRTEX 70, Germany). Powder X-ray diffraction (XRD) was investigated using Cu Kα radiation (λ= 1.54060 Å). The outputs were processed through origin software. Magnetic properties of the catalyst were studied on a Vibrating Sample Magnetometer (VSM) MDKFD, USA. Gas chromatographic analysis was carried out using a GC-2014 chromatograph from Shimadzu, Japan equipped with flame ionization detector (FID) and capillary column (Omegawax,30 m/0.25 mm/0.25 mL). The detector and injector were set at 250 °C and 260 °C, respectively. The oven program was set as 200 °C for 5 min, and then the temperature was increased to 260 °C at a ramping rate of 20 °C/min and kept constant 260 °C for 6 min. Helium was used as a carrier gas at 2mL/min flow-rate. Peganum harmala spice seed and Pistachio leaves were collected from Khuzestan province mountains and identified and approved by Dr. Tamoradi based on morphological and anatomical characters listed in textbook of plant taxonomy.

Graphene oxide (GO) was synthesized by oxidizing graphite powder following a modified Hummers method65. In the typical procedure 2.0 g graphite powder, 1.0 g NaNO3, 6.0 g KMnO4 were mixed to 60 mL concentrated H2SO4 (98%) and vigorously stirred covering in an ice bath for 2 h. It resulted a blackish-green paste which was cooled 35 °C water bath and maintained at this temperature for 2 h. 150 mLdistilled water was then slowly added to it which raised the reaction temperature to 100 °C. The mixture was cooled to 60 °C, 10 mL H2O2 (30%) was then added to the mixture and further stirred for another 2 h. The thick solid obtained was filtered and thoroughly washed with hydrochloric acid (5%) and distilled water for several times until neutral pH. It was dried under vacuum at 60 °C. The GO was exfoliated by sonication for 2 h in water.

Fresh Green pistachio leaves were washed thoroughly with distilled water. 10 g of the leaves were boiled in 100 mL of DI water for 15 min. The mixture was then cooled and filtered through Whatman filter paper No. 1. The filtrate so obtained was stored in refrigerator at 4 °C for further use.

1.0 g GO was dispersed in 100 mL DI water by sonication. A mixture of two salts CuCl2·2H2O (11.43 mmol) and FeCl3·6H2O (22.8 mmol) (molar ratio of Cu2+/Fe3+= 1/2) in 10 mL DI water was added to the dispersion. The pistachio leaf extract (5 mL) was then slowly added to it followed by a NaOH solution (0.1 M) under stirring till it became strongly alkaline (pH=11). After stirring for 2 h, a thick white solid precipitate was obtained which was separated using a magnet. The material was washed with deionized water followed by EtOH and dried in a vacuum oven at 70 °C overnight.

Fresh spice seeds were collected and washed thoroughly with double-distilled water before use. 30 g of the seeds was added to 100 mL of deionized water/ethanol (1:1) and boiled for 15 min in a water bath. It was then cooled and filtered through Whatmann-1 filter paper. A clear filtrate was obtained as the SSE extract. In a separate flask 0.5 g of GO-CuFe2O4was dispersed in 50 mL by sonication for 20 min. The spice seed extract was then added to it and stirred for 24 h at room temperature. The precipitate so obtained was separated by magnetic decantation and washed several times with deionized water. It was dried in a vacuum oven at 40 °C for 12 h to afford the SSE@GO-CuFe2O4 nanocomposite (Fig. 2).

Schematic preparation of SSE@GO-CuFe2O4 nanocomposite.

50 g oil was used in the esterification reaction for 13 experimental runs required in RSM study. For each set, oil was transferred into the reaction flask and preheated in an oil bath up to the reaction temperature. MeOH and the catalyst was then added to it and the mixture was stirred vigorously. After completion (by GC), the catalyst was isolated magnetically and the mixture was allowed to settle in a separating flask for 6 h to separate the biodiesel phases from the byproduct glycerol and methanol-water mixture. The isolated biodiesel layer was further washed with distilled water at 40 °C to remove the residual impurities and concentrated on rotary evaporator at 70 °C. The glycerol is also separately purified for use in its traditional applications (pharmaceutical, cosmetics and food industries).

The catalyst has been prepared by co-precipitation method over the high surface area of GO. Pistachio leaves extract was used for green reduction of the precursor salts into the regularly grown magnetic NPs and also to stabilize them. In order to introduce a basic flavor over the modified magnetic core, the Peganum harmala seed extract was immobilized thereon. The as-synthesized green nanocomposite was characterized by a wide range of physicochemical techniques like FT-IR, SEM, EDX, TEM, elemental mapping, VSM, XRD and TGA.

Fig. 3 depicts the FT-IR spectra of GO, GO-CuFe2O4, Peganum plant extract and the final SSE@GO-CuFe2O4 in order to explain the stepwise construction. In Fig. 3a the FT-IR spectrum of GO is shown where the characteristic peaks appeared at 1052 cm−1, 1402 cm−1, 1735 cm−1 and a broad range peak at 3100-3500 cm−1 corresponding to C-O stretching, the C-OH stretching, carboxyl stretching, C=O stretching and the combined O-H broad and the intercalated water stretching vibrations72,73. The spectrum of GO-CuFe2O4 composite (Fig. 3b) could be detected by the precise peaks for Cu-O and Fe-O stretching vibration in CuFe2O4spinel, being observed at 408 and 584 cm−1 respectively, in addition to all the peaks of GO. This justifies the successful mixing of CuFe2O4 NPs with GO. Fig 3c represents the peganum harmala plant extract showing a broad range of vibrations in the range of 3000-3500 cm−1 attributed to overlapped phenolic O-H and N-H bonds. There are also characteristic vibrations due to carbonyl and carboxyl functions. Finally, the spectrum of SSE doped GO-CuFe2O4 nanocomposite is shown in Fig. 3d, which completely seems to be an amalgam of its component intermediates as well as the plant extract spectrum. This validates an effective overlap or modification of the intermediates over the core NPs.

FT-IR spectra of GO (a), GO-CuFe2O4 (b), plant extract (c) and SSE@GO-CuFe2O4 (d).

In order to assess the comprehensive morphology, shape and texture of the GO, GO-CuFe2O4 composite and the final SSE@GO-CuFe2O4nanocomposite, SEM analysis was carried out and the corresponding outcomes are shown in Fig. 4. GO has a typical flaky appearance with a peel like structure (Fig. 4a). Due to large and two dimensional thin surface the GO sheet seems to be wrinkled53,74. The SEM micrograph of GO-CuFe2O4 displays an assembled particle and sheet morphology, as shown in Fig. 4b. The final material appears almost analogous to Fig. 4b. The presence of a coating of the plant extract can be anticipated over the composite molecule (Fig. 4c,d).

SEM micrograph of GO (a), GO-CuFe2O4 (b) and SSE@GO-CuFe2O4 (c,d).

EDX analysis was carried out to determine the molecular composition of SSE@GO-CuFe2O4nanocomposite, being displayed in Fig. 5. Evidently, it contains Fe and Cu as metallic and C, N, O as non-metallic components. Cu and Fe obviously are corroborated to the CuFe2O4 NPs. The non-metallic components reveals the association of GO and spice seed extract containing the N-heterocycles74. The EDX data were further justified by elemental mapping analysis.

EDX analysis of SSE@GO-CuFe2O4 nanocomposite.

X-ray scanning of a section of the SEM image shows the constituting elements which are uniformly dispersed over the high surface matrix (Fig. 6). Homogeneous dispersion of the active species is an utmost important factor in heterogeneous catalysis better catalytic activity52.

Elemental mapping of SSE@GO-CuFe2O4 nanocomposite.

For magnetic core materials, study of magnetism is a necessary measure. Accordingly, this project went through vibrating sample magnetometric (VSM) study for the GO-CuFe2O4 and SSE@GO-CuFe2O4 nanocomposites and was compared to the unmodified CuFe2O4 NPs. The outcome reveals magnetic hysteresis curves as displayed in Fig. 7. Here, the magnetic curve of pure CuFe2O4 almost overlaps with GO-CuFe2O4 nanocomposite indicating the insertion of GO into the magnetic NP did not have any magnetic impact. Nature of the curves clearly specify that all the materials are of superparamagnetic behavior. Saturation magnetization (Ms) values of them were observed to be 15.1, 15.2 and 6.4 emu/g respectively. The diminished magnetism in the final material is predictable due to the incorporation of non-magnetic spice seed extract into the composite of GO-CuFe2O474.

Magnetic hysteresis curves of CuFe2O4 (red) GO-CuFe2O4 (green) and SSE@GO-CuFe2O4 (blue) nanocomposites.

Thermal stability and toughness of the final nanocomposite was estimated by Thermo-Gravimetric Analysis (TGA). The analysis also helps to determine the biomolecular and organic attachments quantitatively. The related curve forSSE@GO-CuFe2O4 has been presented in Fig. 8. Markedly, it decays continuously starting from 50 °C up to 650 °C with an overall 45% mass loss. An initial 5–6% weight loss occurrstill 150 °C, due to theremoval of moiture and surface hydroxyl groups. Two sharp breaks are detected in the temperature range from 150 °C to 300 °C and 450 °C to 550 °C with a mass loss of 15% each, which are anticipated due to the decomposition of biomolecules of pistachio leaves extract and spice seed extract respectively. This indicates that the catalyst is sufficiently stable for the reaction to carry out74.

Thermo-gravimetric analysis of the SSE@GO-CuFe2O4 nanocomposite.

The crystalline nature and phase structure SSE@GO-CuFe2O4 nanocomposite was analyzed by XRD study, being presented in Fig. 9. The profile was compared to the diffraction pattern of unmodified CuFe2O4 NPs (Fig. 9a). The single phase XRD profile clearly reveals that SSE@GO-CuFe2O4 nanocomposite is a distinct entity and firmly bonded together with all its constituents (Fig. 9b). The broad and weakly crystalline domain in the diffraction angle of 2θ = 10-20º corresponds to the (001) plane of amorphous GO. CuFe2O4 spinel NPs are detected by the diffraction peaks appeared at 2θ = 28°, 34°, 38°, 55°, 57° and 64° attributed to (2 2 0), (3 1 1), (4 0 0), (4 2 2), (5 1 1), (4 4 0) diffraction planes and matches absolutely as Fig. 9a. Obviously, there occurs no significant change in the crystal structure of core CoFe2O4 NP phase even after composite formation with GO and further surface modifications74.

XRD patterns of the CuFe2O4 (a) and SSE@GO-CuFe2O4 (b) nanocomposite.

TEM analysis has been carried out in order to study the particle size and morphology in details. Morphology of SSE@GO-CuFe2O4 nanocomposite in Fig. 10 confirmed that the hard particles are immobilized on the surface of GO layers. The particle sizes were in the range of 30–40 nm.

TEM analysis of SSE@GO-CuFe2O4 nanocomposite.

Following up with the meticulous physicochemical characterization of SSE@GO-CuFe2O4 nanocomposite, the next endeavor was to explore its catalytic activity over the synthesis of biodiesels through transesterification of rapeseed oil and waste corn oil (Fig. 11). Here, the reaction protocol has been standardized through response surface methodology (RSM), an advanced mathematical model, other than the typical method of condition optimizations. RSM involves a sequential process that goes through a practical and logical operating reaction process and includes models building, design of experiment and statistics which ultimately stimulates the optimization parameters. RSM is based on Box–Behnken statistical model that leads to the maximum yield of product. In this process, three different reaction parameters, viz., catalyst concentration, methanol to oil molar ratio and time (h), are investigated within a certain range, as documented in Table 1. Subsequently, a series of experiments, usually 13 runs, are conducted to acquire the best optimized result. A mathematical model is applied to validate the experimental results47. In this study the catalyst concentration and the methanol to oil ratio were limited within 3 to 8 w/V % and 10 to 16 respectively. Similarly, the reaction time was limited to 4 to 7 h.

Transesterification of glycerol esters with MeOH over nanomagnetic SSE@GO-CuFe2O4 catalyst.

Thereafter, this work was carried out following 13 experiments maintaining these parameter ranges and the resulting data are produced in Table 2. Among the three variables, the alternation of catalyst concentration was found to be the most vital, for both rapeseed oil as well as waste-corn oil. The best possible yield of biodiesel for these two substrates were obtained as 92.81% and 87.26% respectively, involving 8% w/v catalyst concentration at M:O of 13:1 and 7 h of reaction time (entry 11, Table 2).

The set of optimized parameters obtained by RSM analysis was further interconnected to coefficients of interactions, linear and quadratic effects by Analysis of variance (ANOVA). The probability values for correlation coefficients and variable parameters for each model has been shown in Tables 3 and 4 for rapeseed oil and waste corn oil respectively. In Table 3 the P values for the model is 0.0005. P-values less than 0.0500 indicate model terms are significant and AA, CC, AC, BC, A2 are significant model terms. Values greater than 0.1000 indicate the model terms are not significant. The Model F-value of 18.30 implies the model is significant. There is only a 0.05% chance that an F-value this large could occur due to noise. The Predicted R2 of 0.3478 is not as close to the Adjusted R2 of 0.9068 as one might normally expect. Adeq Precision, which measures the signal to noise ratio, is found 15.509. The ratio greater than 4 is highly desirable. This model indicates an adequate signal and can be used to navigate the design space75.

In Table 4, The Model F-value of 7.14 and P-values less than 0.0500 implies that the model is significant. There is only a 0.44% chance of F-value to deviate due to noise. Here AA is a significant model term. Values greater than 0.1000 indicate the model terms are not significant. Here also, the Predicted R2 of 0.2094 is not as close to the Adjusted R2 of 0.5351 and may indicate a large block effect or a possible problem with your model and/or data. But the Adeq Precision ratio is 8.247 (> 4.0) indicating an adequate signal. This model also can be used to navigate the design space.

Subsequently, the regression model developed through ANOVA was justified by plotting the experimental or actual values of the parameters against the predicted values. Evidently, the parameter values are in close agreement for both rapeseed oil and waste corn oil (Fig. 12). This signifies that the regression model can explain the connection between independent variables and the response, biodiesel yield. All the values are leaning towards a mean straight line and the chance of errors are insignificant.

The comparison of predicted value against the actual value by the RSM in rapeseed oil (a) and waste corn oil (b).

In order to explain the effect of independent variables on the biodiesel yields, the 3-D response surface contour plots are drawn with the help of RSM. In the contour plot Fig. 13a,c, the optimization of biodiesel yield (%) has been displayed with variable catalyst concentration and methanol/oil ratio for rapeseed oil and waste corn oil respectively, over a constant time period of7 h. In Fig. 13a the productivity increases as a hyperbolic plane and 13c as a linear plane with increase in catalyst concentration from 3% w/v to 8%w/v and decrease in the M:O from 16:1 to 10:1. The best value was obtained at catalyst concentration of 8%w/v and the M:O of 13:1 in both the substrates. Similarly, Fig. 13b,d represents the optimization of biodiesel yield (%)with different catalyst concentration and time for rapeseed oil and waste corn oil respectively, over a constant methanol/oil ratio of 13:1. Here also in Fig. 13b,d, the % biodiesel yield increases as a hyperbolic and linear plane with increase in catalyst concentration from 3% w/v to 8%w/v and increase in time from 4 to 7 h respectively. In this two plots too yield increases with increase in catalyst concentration from 3 to 8% and increase in time from 4 to 7 h and the best result was found at 8%w/v catalyst concentration and 7 h of reaction time.

3D response surface plots of catalyst concentration and M:O for rapeseed oil (a); catalyst concentration and time for rapeseed oil (b); catalyst concentration and M:O for waste corn oil (c); catalyst concentration and time for waste corn oil (d).

This work has been compared with the previously reported ones and been documented in Table 5. This clearly demonstrates that our work is greatly advantageous in terms of high efficiency, eco-sustainability, easy magnetic separation and also involvement of green material in the novel catalyst in contrast to previously reported works. Being a heterogeneous catalyst, reusability of the material is very important. Interestingly, the catalyst was used three times in succession without considerable loss in its reactivity. After the 4th run the productivity went down abruptly, might be due to leaching of active site from the nanocomposite surface.

In conclusion, we have demonstrated the engineered synthesis of a novel high surface area magnetic nanocomposite material (SSE@GO-CuFe2O4) following post-synthetic modification approach. Pistachio leaves extract was used in the green synthesis of GO-CoFe2O4nanocomposite. A spice seed of Peganum harmala, containing numerous organo-basic compounds were immobilized over the nanocomposite in order to exploit the basicity of the compounds as well as the high surface area of GO and magnetically retrievability of CuFe2O4. The green synthesized featured material was justified and analyzed by different physicochemical techniques like FT-IR, SEM, TEM, EDX, elemental mapping, XRD and VSM. Thereafter, the material was applied in the transesterification of rapeseed oil and waste corn oil to their methylated biodiesels with high efficacy. The basic biomolecules of spice seed extract facilitated the synthesis of biodiesels. Response surface methodology (RSM) was used for optimization of different reaction parameters like methanol to oil ratio, catalyst concentration and temperature. Based on the results, the optimum yield of the corresponding biodiesel rapeseed oil and waste corn oil were obtained at M:O of ~ 13:1 and a catalyst concentration of ~ 8%w/v at 65 °C in 7 h reaction time. The results were further validated over ANOVA and 3D response surface contour plots. The outputs obtained from our devised protocol definitely would add an impact on the use of bio-functionalized nanocatalysts towards the synthesis of bio-diesels following a sustainable pathway. In addition, the RSM methodology also would be used more frequently in the optimization of different catalytic reactions in order to have more précised results.

All data generated or analyzed during this study are included in this published article.

Fourier-transform infrared spectroscopy

Scanning electron microscopy

Transmission electron microscopy

Energy dispersive X-ray

X-ray diffraction

Thermogravimetric analysis

Vibrating sample magnetometer

Response surface methodology

Analysis of variance

Thanh, L. T., Okitsu, K., Van Boi, L. & Maeda, Y. Catalytic technologies for biodiesel fuel production and utilization of glycerol. A review. Catalysts 2, 191–222 (2012).

Article CAS Google Scholar

Glisic, S. B., Pajnik, J. M. & Orlović, A. M. Process and techno-economic analysis of green diesel production from waste vegetable oil and the comparison with ester type biodiesel production. Appl. Energy 170, 176–185 (2016).

Article CAS Google Scholar

Bobadilla Corral, M., LostadoLorza, R., EscribanoGarcía, R., Somovilla Gómez, F. & Vergara González, E. P. An improvement in biodiesel production fromwaste cooking oil by applying thought multi-response surface methodology using desirability functions. Energies 10, 130–137 (2017).

Article Google Scholar

Martins, F., Felgueiras, C., Smitkova, M. & Caetano, N. Analysis of fossil fuel energy consumption and environmental impacts in European countries. Energies 12(6), 964 (2019).

Article CAS Google Scholar

Narula, K. Global energy system and sustainable energy security. Maritime Dimen Sustain. Energy Secur. 68, 23–49 (2019).

Article Google Scholar

Abas, N., Kalair, A. & Khan, N. Review of fossil fuels and future energy technologies. Futures 39, 31–49 (2015).

Article Google Scholar

Tan, Y. H. et al. Biodiesel production from used cooking oil using green solid catalyst derived from calcined fusion waste chicken and fish bones. Renew. Energy 139, 696–706 (2019).

Article CAS Google Scholar

Tang, X. & Niu, S. Preparation of carbon-based solid acid with large surface area to catalyze esterification for biodiesel production. J. Ind. Eng. Chem. 69, 187–195 (2019).

Article CAS Google Scholar

Norjannah, B., Chyuan Ong, H., Masjuki, H. H., Juan, J. C. & Chong, W. T. Enzymatic transesterification for biodiesel production from used cooking oil, a review. RSC Adv. 6, 60034–60055 (2016).

Article ADS CAS Google Scholar

Fukuda, H., Kondo, A. & Noda, H. Biodiesel fuel production by transesterification of oils. J. Biosci. Bioenergy 92, 405–416 (2001).

Article CAS Google Scholar

Verma, P. & Sharma, M. Comparative analysis of effect of methanol and ethanol on Karanja biodiesel production and its optimization. Fuel 180, 164–174 (2016).

Article CAS Google Scholar

Ong, H. et al. Production and comparative fuel properties of biodiesel from non-edible oils: Jatropha curcas, Sterculiafoetida and Ceibapentandra. Energy Convers. Manag. 73, 245–255 (2013).

Article CAS Google Scholar

Konur, O. Palm oil-based biodiesel fuels: A review of the research. Biodivers. Fuel Based Edible Nonedible 2021 (in press).

Gayglou, S. E., Tafakori, V., Zahed, M. A., Khamoushi, A.: Two promoters of biodiesel and biomass production induced by different concentrations of myo-inositol in Chlorella vulgaris. Biomass Convers. Biorefinery 2021 (in press).

Singh, D. et al. A review on feedstocks, production processes, and yield for different generations of biodiesel. Fuel 262, 116553–116565 (2020).

Article CAS Google Scholar

Hasni, K., Ilham, Z., Dharma, S. & Varman, M. Optimization of biodiesel production from Bruceajavanica seeds oil as novel non-edible feedstock using response surface methodology. Energy Convers. Manag. 149, 392–400 (2017).

Article CAS Google Scholar

Souza, M. C. G., de Oliveira, M. F., Vieira, A. T., de Faria, A. M. & Batista, A. C. F. Methylic and ethylic biodiesel production from crambe oil (Crambeabyssinica): New aspects for yield and oxidative stability. Renew. Energy 163, 368–374 (2021).

Article Google Scholar

Ma, F. & Hanna, M. A. Biodiesel production: A review. Bioresour. Technol. 70, 1–15 (1999).

Article CAS Google Scholar

Lapinskiene, A., Martinkus, P. & Rebzdaite, V. Eco-toxicological studies of diesel and biodiesel fuels in aerated soil. Environ. Pollut. 142, 432–437 (2006).

Article CAS PubMed Google Scholar

Knothe, G., Gerpen, J. V. & Krahl, J. The biodiesel handbook. AOCS 34, 1–3 (2005).

Google Scholar

Mumtaz, M. W., Adnan, A., Mukhtar, H., Rashid, U. & Danish, M. Biodiesel production through chemical and biochemical transesterification. Clean Energy Sustain. Dev. 15, 465–485 (2017).

Article Google Scholar

Baskar, G., Kalavathy, G., Aiswarya, R. & Selvakumari, I. A. Advances in bio-oil extraction from non-edible oil seeds and algal biomass. Adv. Eco-Fuels Sustain. Environ. 7, 187–210 (2019).

Article Google Scholar

Nasreen, S. et al. Review of catalytic transesterification methods for biodiesel production. Biofuel State Dev. 6, 1–28 (2018).

Google Scholar

Norjannah, B., Chyuan Ong, H., Masjuki, H. H., Juan, J. C. & Chong, W. T. Enzymatic transesterification for biodiesel production: a comprehensive review. RSC Adv. 6, 60034–60055 (2016).

Article ADS CAS Google Scholar

Angulo, B., Fraile, J. M., Gil, L. & Herrerías, C. I. Comparison of chemical and enzymatic methods for the transesterification of waste fish oil fatty ethyl esters with different alcohols. ACS Omega 5, 1479–1487 (2020).

Article CAS PubMed PubMed Central Google Scholar

Wang, X. et al. Fatty acid methyl ester synthesis through transesterification of palm oil with methanol in microchannels: flow pattern and reaction kinetics. Energy Fuels 34, 3628–3639 (2020).

Article CAS Google Scholar

Yusuff, A. S. & Bello, K. A. Synthesis of fatty acid methyl ester via transesterification of waste frying oil by a zinc-modified pumice catalyst: Taguchi approach to parametric optimization. React. Kinet. Mech. Cat. 128, 739–761 (2019).

Article CAS Google Scholar

Maleki, H. et al. Transesterification of canola oil and methanol by lithium impregnated CaO–La2O3 mixed oxide for biodiesel synthesis. J. Ind. Eng. Chem. 47, 399–404 (2017).

Article CAS Google Scholar

Shareh, F. B., Kazemeini, M., Asadi, M. & Fattahi, M. Metal promoted mordenite catalyst for methanol conversion into light olefins. Petrol. Sci. Tech. 32, 1349–1356 (2014).

Article CAS Google Scholar

Amirthavalli, V. & Warrier, A. R. Fabrication and optimization of nanocatalyst for biodiesel production: An overview. AIP Conf. Proc. 2115, 030609–030612 (2019).

Google Scholar

Pedram, M. Z., Kazemeini, M., Fattahi, M. & Amjadian, A. A physicochemical evaluation of modified HZSM-5 catalyst utilized for production of dimethyl ether from methanol. Pet. Sci. Tech. 32, 904–911 (2014).

Article CAS Google Scholar

Kamyab, H. et al. Optimum lipid production using agro-industrial wastewater treated microalgae as biofuel substrate. Clean Technol. Environ. Policy 18, 2513–2523 (2016).

Article CAS Google Scholar

Kamyab, H. et al. Isolation and screening of microalgae from agro-industrial wastewater (POME) for biomass and biodiesel sources. Desalin. Water Treat. 57, 29118–29125 (2016).

Article CAS Google Scholar

Parichehreh, R., Gheshlaghi, R., Mahdavi, M. A. & Kamyab, H. Investigating the effects of eleven key physicochemical factors on growth and lipid accumulation of Chlorella sp. as a feedstock for biodiesel production. J. Biotechnol. 340, 64–74 (2021).

Article CAS PubMed Google Scholar

Vicente, G., Martınez, M. & Aracil, J. Integrated biodiesel production: A comparison of different homogeneous catalysts systems. Biores. Technol. 92, 297–305 (2004).

Article CAS Google Scholar

Boey, P.-L., Maniam, G. P. & Hamid, S. A. Performance of calcium oxide as a heterogeneous catalyst in biodiesel production: A review. Chem. Eng. J. 168, 15–22 (2011).

Article CAS Google Scholar

Singh, B., Gulde, A., Rawat, I. & Bux, F. Towards a sustainable approach for development of biodiesel from plant and microalgae. Renew Sustain. Energy Rev. 29, 216–245 (2014).

Article CAS Google Scholar

Takagaki, A. et al. Esterification of higher fatty acids by a novel strong solid acid. Catal. Today 116, 157–161 (2006).

Article CAS Google Scholar

Konwar, L. J., Boro, J. & Deka, D. Review on latest developments in biodiesel production using carbon-based catalysts. Renew Sustain. Energy Rev. 29, 546–564 (2014).

Article CAS Google Scholar

Tariq, M., Ali, S. & Khalid, N. Activity of homogeneous and heterogeneous catalysts, spectroscopic and chromatographic characterization of biodiesel: a review. Renew. Sustain. Energy Rev 16, 6303–6316 (2012).

Article CAS Google Scholar

Gotch, A. J., Reeder, A. J. & McCormick, A. Study of heterogeneous base catalysts for biodiesel production. J. Undgrad. Chem. Res 8, 22–26 (2009).

CAS Google Scholar

Chouhan, A. P. S. & Sarma, A. K. Modern heterogeneous catalysts for biodiesel production: A comprehensive review. Renew. Sustain. Energy Rev. 15, 4378–4399 (2011).

Article CAS Google Scholar

Leung, D. Y. C., Wu, X. & Leung, M. K. H. A review on biodiesel production using catalyzed transesterification. Appl. Energy 87, 1083–1095 (2010).

Article CAS Google Scholar

Zabeti, M., Daud, W. A. W. & Aroua, M. K. Activity of solid catalysts for biodiesel production: a review. Fuel Process. Technol. 90, 770–777 (2009).

Article CAS Google Scholar

Macario, A. & Giordano, G. Catalytic conversion of renewable sources for biodiesel production: A comparison between biocatalysts and inorganic catalysts. Catal. Lett. 143, 159–168 (2013).

Article CAS Google Scholar

Sani, Y. M., Daud, W. A. W. & Aziz, A. R. A. Activity of solid acid catalyst for biodiesel production: a critical review. Appl. Catal. A Gen. 470, 140–161 (2014).

Article CAS Google Scholar

Lam, M. K., Lee, K. T. & Mohamed, A. R. Homogeneous, heterogeneous and enzymatic catalysis for transesterification of high free fatty acid oil (waste cooking oil) to biodiesel: a review. Biotechnol. Adv. 28, 500–518 (2010).

Article CAS PubMed Google Scholar

Shu, Q. et al. Synthesis of biodiesel from cottonseed oil and methanol using a carbon-based solid acid catalyst. Fuel Process. Technol. 90, 1002–1008 (2009).

Article CAS Google Scholar

Smith, S. M. et al. Transesterification of soybean oil using bovine bone waste as new catalyst. Bioresour. Technol. 143, 686–690 (2013).

Article CAS PubMed Google Scholar

Luque, R. et al. Carbonaceous residues from biomass gasification as catalysts for biodiesel production. J. Nat. Gas Chem. 21, 246–250 (2012).

Article CAS Google Scholar

Sanjay, B. Heterogeneous catalyst derived natural resources for biodiesel production: A review. Res. J. Chem. Sci. 3, 95–101 (2013).

Google Scholar

Veisi, H., Tamoradi, T., Rashtiani, A., Hemmati, S. & Karmakar, B. Palladium nanoparticles anchored polydopamine-coated graphene oxide/Fe3O4 nanoparticles (GO/Fe3O4@PDA/Pd) as a novel recyclable heterogeneous catalyst in the facile cyanation of haloarenes using K4[Fe(CN)6] as cyanide source. J. Ind. Eng. Chem. 90, 379–388 (2020).

Article CAS Google Scholar

Tamoradi, T. et al. MgO doped magnetic graphene derivative as a competent heterogeneous catalyst producing biofuels via transesterification: Process optimization through Response Surface Methodology (RSM). J. Environ. Chem. Eng. 9, 106009–106020 (2021).

Article CAS Google Scholar

Rao, L. et al. Lotus seedpods biochar decorated molybdenum disulfide for portable, flexible, outdoor and inexpensive sensing of hyperin. Chemosphere 301, 134595 (2022).

Article ADS CAS PubMed Google Scholar

Torkian, N. et al. Synthesis and characterization of Ag-ion-exchanged zeolite/TiO2 nanocomposites for antibacterial applications and photocatalytic degradation of antibiotics. Environ. Res. 207, 112157 (2022).

Article CAS PubMed Google Scholar

Cheraghi, A., Davar, F., Homayoonfal, M. & Hojjati-Najafabadi, A. Effect of lemon juice on microstructure, phase changes, and magnetic performance of CoFe2O4 nanoparticles and their use on release of anti-cancer drugs. Ceram. Int. 47, 20210–20219 (2021).

Article CAS Google Scholar

HojjatiNajafabadi, A., Ghasemi, A., Mozaffarinia, R. Synthesis and evaluation of microstructural and magnetic properties of Cr3+ substitution barium hexaferrite nanoparticles (BaFe10.5−x Al1.5Cr x O19). J. Cluster Sci. 27, 965–978 (2016).

Hojjati-Najafabadi, A., Davar, F., Enteshari, Z., Hosseini-Koupaei, M. Antibacterial and photocatalytic behaviour of green synthesis of Zn0. 95Ag0.05O nanoparticles using herbal medicine extract. Ceram. Int. 31617–31624 (2021).

Hojjati-Najafabadi, A., Mansoorianfar, M., Liang, T., Shahin, K. & Karimi-Maleh, H. A review on magnetic sensors for monitoring of hazardous pollutants in water resources. Sci. Total Environ. 824, 153844 (2022).

Article ADS CAS PubMed Google Scholar

Karimi-Maleh, H. et al. Recent advances in carbon nanomaterials-based electrochemical sensors for food azo dyes detection. Food Chem. Toxicol. 164, 112961 (2022).

Article CAS PubMed Google Scholar

Karaman, C., Karaman, O., Show, P. L., Karimi-Maleh, H. & Zare, N. Congo red dye removal from aqueous environment by cationic surfactant modified-biomass derived carbon: Equilibrium, kinetic, and thermodynamic modeling, and forecasting via artificial neural network approach. Chemosphere 290, 133346 (2022).

Article ADS CAS PubMed Google Scholar

Karimi-Maleh, H. et al. Cyanazine herbicide monitoring as a hazardous substance by a DNA nanostructure biosensor. J Hazardous Mater. 423, 127058 (2022).

Article CAS Google Scholar

Karimi-Maleh, H., Karaman, C., Karaman, O., Karimi, F., Vasseghian, Y., Fu, L., Baghayeri, M., Rouhi, J., Kumar, P. S., Show, P. L., Rajendran, S., Sanati, A. L., Mirabi, A. Nanochemistry approach for the fabrication of Fe and N co-decorated biomass-derived activated carbon frameworks: a promising oxygen reduction reaction electrocatalyst in neutral media. J. Nanostruct. Chem. in press (2022).

Ghalkhani, M. et al. Recent advances in Ponceau dyes monitoring as food colorant substances by electrochemical sensors and developed procedures for their removal from real samples. Food Chem. Toxicol. 161, 112830 (2022).

Article CAS PubMed Google Scholar

Karimi-Maleh, H. et al. A green and sensitive guanine-based DNA biosensor for idarubicin anticancer monitoring in biological samples: A simple and fast strategy for control of health quality in chemotherapy procedure confirmed by docking investigation. Chemosphere 291, 132928 (2022).

Article ADS CAS PubMed Google Scholar

Moloudizargari, M., Mikaili, P., Aghajanshakeri, S., Asghari, M. H. & Shayegh, J. Pharmacological and therapeutic effects of Peganumharmala and its main alkaloids. Pharmacogn. Rev. 7, 199–212 (2013).

Article PubMed PubMed Central Google Scholar

Wang, K.-B., Li, D.-H., Bao, Y. & Cao, F. Structurally diverse alkaloids from the seeds of Peganumharmala. J. Nat. Prod. 80, 551–559 (2017).

Article CAS PubMed PubMed Central Google Scholar

Miao, X., Zhang, X., Yuan, Y., Zhang, Y. & Gao, J. The toxicity assessment of extract of Peganumharmala L. seeds in Caenorhabditis elegans. BMC Complement. Med. Ther. 20, 256–267 (2020).

Article CAS PubMed PubMed Central Google Scholar

Singh, V., Belova, L., Singh, B. & Sharma, Y. C. Biodiesel production using a novel heterogeneous catalyst, magnesium zirconate (Mg2Zr5O12): Process optimization through response surface methodology (RSM). Energy Convers. Manag. 174, 198–207 (2018).

Article CAS Google Scholar

Tan, Y. H., Abdullah, M. O., Hipolito, C. N. & Zauzi, N. S. A. Application of RSM and Taguchi methods for optimizing the transesterification of waste cooking oil catalyzed by solid ostrich and chicken-eggshell derived CaO. Renew. Energy 114, 437–447 (2017).

Article CAS Google Scholar

Arumugam, A., Thulasidharan, D. & Jegadeesan, G. B. Process optimization of biodiesel production from Heveabrasiliensis oil using lipase immobilized on spherical silica aerogel. Renew. Energy 116, 755–761 (2018).

Article CAS Google Scholar

Mansoorianfar, M., Shahin, K., Hojjati-Najafabadi, A. & Pei, R. MXene–laden bacteriophage: A new antibacterial candidate to control bacterial contamination in water. Chemosphere 290, 133383 (2022).

Article ADS CAS PubMed Google Scholar

HojjatiNajafabadi, A., Mozaffarinia, R., Rahimi, H., ShojaRazavi, R. & Paimozd, E. Mechanical property evaluation of corrosion protection sol–gel nanocomposite coatings. Surf. Eng. 29, 249–254 (2013).

Article CAS Google Scholar

Tamoradi, T., Kiasat, A. R., Veisi, H., Nobakht, V. & Karmakar, B. Transesterification of rapeseed oil and waste corn oil toward the production of biodiesel over a basic high surface area magnetic nanocatalyst: application of the response surface methodology in process optimization. New. J. Chem. 45, 21116–21124 (2021).

Article CAS Google Scholar

Jang, M. G., Kim, D. K., Park, S. C., Lee, J. S. & Kim, S. W. Biodiesel production from crude canola oil by two-step enzymatic processes. Renew Energ 42, 99–104 (2012).

Article CAS Google Scholar

Kim, H. J. et al. Transesterification of vegetable oil to biodiesel using heterogeneous base catalyst. Catal. Today 93, 315–320 (2004).

Article Google Scholar

Nelson, L. A., Foglia, A. & Marmer, W. N. Lipase-catalyzed production of biodiesel. J. Am. Oil Chem. Sot. 73, 1191–1195 (1996).

Article CAS Google Scholar

Antunes, W. M., Veloso, C. O. & Henriques, C. A. Transesterification of soybean oil with methanol catalyzed by basic solids. Catal. Today 133, 548–554 (2008).

Article Google Scholar

Mittelbach, M. Lipase catalyzed alcoholysis of sunflower oil. J. Am. Oil Chem. Sot. 67, 1688170 (1990).

Google Scholar

Abigor, R. et al. Lipase-catalysed production of biodiesel fuel from some Nigerian lauric oils. Biochem. Sot. Trans. 28, 979–981 (2000).

Article CAS Google Scholar

Download references

The authors are grateful to Iran National Science Foundation (INSF) for financial support provided by the post-doctoral Project (98001691). We also appreciate Shahid Chamran University of Ahvaz Research Council for their help and supports. The study is in compliance with relevant institutional, national, and international guidelines and legislation.

Department of Chemistry, Faculty of Sciences, Shahid Chamran University of Ahvaz, Ahvaz, Iran

Taiebeh Tamoradi, Ali Reza Kiasat & Valiollah Nobakht

Department of Chemistry, Production Technology Research Institute-ACECR, Ahvaz, Iran

Taiebeh Tamoradi

Department of Chemistry, Payame Noor University, Tehran, 19395-4697, Iran

Hojat Veisi

Department of Chemistry, Gobardanga Hindu College, 24-Parganas (North), Gobardanga, India

Bikash Karmakar

You can also search for this author in PubMed Google Scholar

T.T., A.R.K., H.V., V.N. and B.K.: Visualization, Writing original draft, Formal analysis. T.T., A.R.K., V.N. and H.V.: Funding acquisition, Methodology, Supervision. B.K.: Writing original draft, Formal analysis, Writing-review and editing.

Correspondence to Ali Reza Kiasat or Hojat Veisi.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Tamoradi, T., Kiasat, A.R., Veisi, H. et al. RSM process optimization of biodiesel production from rapeseed oil and waste corn oil in the presence of green and novel catalyst. Sci Rep 12, 19652 (2022). https://doi.org/10.1038/s41598-022-20538-4

Download citation

Received: 21 December 2021

Accepted: 14 September 2022

Published: 16 November 2022

DOI: https://doi.org/10.1038/s41598-022-20538-4

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

Scientific Reports (2023)

Catalysis Letters (2023)

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.

Enhancement of adsorption efficiency of crystal violet and chlorpyrifos onto pectin hydrogel@Fe3O4

News

RSM process optimization of biodiesel production from rapeseed oil and waste corn oil in the presence of green and novel catalyst